Description AC3-03

From KBwiki
Revision as of 12:54, 15 September 2008 by Tonyh (talk | contribs)
Jump to navigation Jump to search

Cyclone separator

Application Challenge 3-03 © copyright ERCOFTAC 2004


Introduction

Cyclone chambers (cyclones) are used in many industrial processes. Typical applications for cyclones include two phase separation, liquid clarification, slurry thickening, solids washing, degassing of liquids, solids classification/sorting and for the separation of immiscible liquids 1.

This wide range of applications has resulted in the development of many alternative designs of cyclone with the design optimised in respect of the specific application.

A cyclone design type commonly used in industry is cono-cylindrical. A design of this type is shown in Figure 1. The key geometrical features of this type of cyclone are identified in the figure.


Image281.gif



Figure 1 A conventional cono-cylindrical cyclone [1] The type of cyclone shown in Figure 1 uses either a single or a multiple set of tangential inlets. The inflowing fluid rotates within the main body of the chamber and is constrained to follow a spiral flow path. Any particles suspended within the fluid are subjected to an enhanced radial acceleration. Cyclones are commonly used when the density of the inflowing fluid (the carrier phase) is less than the particle phase. In cyclones of this type the larger particles migrate outwards to the cone wall where they travel in a downward spiral to the base of the chamber and exit at the underflow. The smaller particles migrate more slowly and therefore their distribution across the flow changes little. Those in the centre are captured in the upward flow and spiral upward and out through the vortex finder, see Figure 1. The remainder are discharged with the coarse fraction at the underflow or spigot.

The application challenge (AC) described in this document focused on a cyclone of the type shown in Figure 1. CFD simulations were carried out and the predicted axial and tangential velocity components were compared with published experimental data. The domain was represented using a relatively coarse unstructured hexahedral mesh. The Reynolds stress turbulence model was used.

The Fluent CFD software version 5.0 was used throughout the study.


Relevance to Industrial Sector

The absence of moving parts and simple compact construction combined with a high volume of material throughput make the cyclone a convenient and practical tool for industrial applications, many of which are still being explored.

Rietema 2 carried out some of the first experimental optimisation studies that built upon the work of Kelsall 3. The results of such studies have been used to develop empirical based design criteria. Numerical and analytical studies of the flow in cyclones have also been carried out, the most notable by Bloor and Ingham 4. As stated by Slack and Wraith 5, this approach requires simplifying assumptions about the Navier-Stokes equations aimed at establishing a solvable analytical model. Clearly, therefore, CFD can be used to further develop the design of cyclones and for the design of non-standard cyclones where empirical or simplified models may be inadequate. The development of an accurate CFD cyclone modelling technique would also address the need for a reliable computer design model for cyclones called for by Knowlton 6.


Design or Assessment Parameters

The assessment parameters used for the purpose of this AC were the mean axial and tangential velocity profiles on a number of radial lines through a cyclone chamber with the location of each radial profile identified in Figure 2.


Flow Domain Geometry

The geometry of the cyclone used for the purpose of the AC is shown in Figure 2.

The geometry described here is not available in digital format, however, sufficient detail of the key geometry dimensions is provided in Figure 2 to enable the geometry to be fully reproduced. Please note the dimensions shown are internal dimensions and if felt significant the inlet duct can be included within the model.


Image282.gif




Figure 2 The geometry of the cyclone used for the Application Challenge

Flow Physics and Fluid Dynamics Data

The flow physics were turbulent, incompressible and isothermal. The inlet Reynolds number was in the range 1E4 to 1E5 as based on the mean inlet duct diameter.

The fluid used in the experiments was air, however, no data on the fluid properties were specified. A density and viscosity based on atmospheric pressure and a temperature of 17°C were therefore assumed and this resulted in the following fluid properties: density = 1.225kg/m3 and viscosity = 1.7894E-5 kg/ms.


© copyright ERCOFTAC 2004


Contributors: Chris Carey - Fluent Europe Ltd

Site Design and Implementation: Atkins and UniS

       Top        	      Next