DNS 1-6 Description: Difference between revisions

From KBwiki
Jump to navigation Jump to search
Line 50: Line 50:
==Boundary conditions==
==Boundary conditions==


The computational set-up aims at replicating the flow conditions of the experiment but with a halved incoming boundary layer thickness. To enforce these conditions in an efficient and accurate manner a Blasius velocity profile corresponding to <math>Re_x=900\,000</math> and free stream velocity <math>u_{\infty}=u_{ref}</math> is imposed at the inlet together with uniform static pressure <math>p_{inflow}=p_{ref}</math>. and total temperature <math>T_{t,inflow}=T_{ref}\left[1+0.5\left(\gamma-1\right){Ma}^{2}\right]</math>. A laminar boundary layer is then established, and a flow perturbation is applied at <math>Re_x=950\,000</math> to trigger transition to turbulence following the idea of [[lib:DNS_1-6_description#5|Housseini ''et&nbsp;al.'' (2016)]] and [[lib:DNS_1-6_description#6|Schlatter and Örlü (2012)]].
The computational set-up aims at replicating the flow conditions of the experiment but with a halved incoming boundary layer thickness. To enforce these conditions in an efficient and accurate manner a Blasius velocity profile corresponding to <math>Re_x=900\,000</math> and free stream velocity <math>u_{\infty}=u_{ref}</math> is imposed at the inlet together with uniform static pressure <math>p_{inflow}=p_{ref}</math>. and total temperature <math>T_{t,inflow}=T_{ref}\left[1+0.5\left(\gamma-1\right){Ma}^{2}\right]</math>.
A laminar boundary layer is then established, and a flow perturbation is applied at <math>Re_x=950\,000</math> to trigger transition to turbulence following the idea of [[lib:DNS_1-6_description#5|Housseini ''et&nbsp;al.'' (2016)]] and [[lib:DNS_1-6_description#6|Schlatter and Örlü (2012)]].
The distance of the inlet boundary from the wing-body junction is defined such that the incoming turbulent boundary layer reaches a thickness <math>\delta_{99.5}/T=0.25</math> (half of the experimental value) at a given point, hereinafter referred as checkpoint, upstream the airfoil leading edge, i.e., at <math>x_{ckp}/T=-2.15</math>.
The distance of the inlet boundary from the wing-body junction is defined such that the incoming turbulent boundary layer reaches a thickness <math>\delta_{99.5}/T=0.25</math> (half of the experimental value) at a given point, hereinafter referred as checkpoint, upstream the airfoil leading edge, i.e., at <math>x_{ckp}/T=-2.15</math>.
To define such distance, a precursory computational campaign for the turbulent flow over a flat plate was performed.
To define such distance, a precursory computational campaign for the turbulent flow over a flat plate was performed.
According to the outcomes of this campaign, the inlet boundary is positioned at <math>x/T=-12.75</math>.
According to the outcomes of this campaign, the inlet boundary is positioned at <math>x/T=-12.75</math>.
The tripping term promoting the boundary layer transition is then located at <math>x/T=-12.3</math>.
The tripping term promoting the boundary layer transition is then located at <math>x/T=-12.3</math>, see [[lib:DNS_1-6_description#figure2|Fig. 2]].
At the outlet boundary, placed at <math>x/T=50</math>, the static pressure <math>{p_{outflow}=p_{ref}}</math> is imposed with an exit-pressure outflow boundary condition.
At the outlet boundary, placed at <math>x/T=50</math>, the static pressure <math>{p_{outflow}=p_{ref}}</math> is imposed with an exit-pressure outflow boundary condition.
The bottom boundary is an adiabatic solid wall type (no slip) for <math>-12.75\leq x/T\leq 17</math> and symmetry type for <math>x/T>17</math>.
The bottom boundary is an adiabatic solid wall type (no slip) for <math>-12.75\leq x/T\leq 17</math> and symmetry type for <math>x/T>17</math>.

Revision as of 18:26, 21 February 2023


Front Page

Description

Computational Details

Quantification of Resolution

Statistical Data

Instantaneous Data

Storage Format

Introduction

This test case considers the flow around a wing mounted on a flat plate, which is representative of the wing-body junction flow problems encountered in applications of aeronautical interest. The flow features the interaction between the incipient turbulent boundary layer and the mounted airfoil, and the main physical phenomenon of interest is the horseshoe vortex developing at the junction and the corner separation. This flow is also highly 3D and anisotropic regarding the turbulent stresses. Establishing a DNS database of this flow is of crucial interest since it has been shown that RANS models (both Boussinesq and Reynolds stresses-based models) display strong difficulties in recovering data from the available experiments. Such a database allows for a more thorough availability of the flow field with respect to the experiments and gives the possibility of using Machine Learning or data-assimilation techniques to improve standard RANS models.

Review of previous studies and choice of test case

A thorough listing of existing experimental and numerical studies regarding wing-body junction flows can be found in Gand et al. (2010). The present uDNS is based on the configuration considered in the simulations by Apsley and Leschziner (2001), who were based themselves on the experimental studies by Devenport and Simpson (1990) and Fleming et al. (1995). The Reynolds number based on the airfoil thickness is similar to the experiment and its value is . The flow is almost incompressible with a Mach number based on the freestream velocity of . The uDNS setup reproduces the experimental conditions but with half the experimental impacting boundary layer thickness. Therefore a direct comparison with the experimental results is not possible for the present uDNS.

Description of the test case

Geometry and flow parameters

Fig. 2 displays a view of the computational domain. The reference length scale is the wing thickness , see Fig. 2, and the corresponding Reynolds number is . The wing is formed by a 3:2 semi-elliptic nose with a NACA0020 tail profile and the resulting chord-to-thickness ratio is . The computational domain size is in the streamwise direction, in the spanwise direction and in the wall-normal direction, see Fig. 3. The coordinate origin is located at the root leading edge of the airfoil. There is no flow incidence relatively to the wing, corresponding to an angle of attack of degrees. Parameters of the flow (air with , , ) are reported in Tab. 1.

DNS1-6 Wing-body junction wing thickness.png
Figure 2: Wing-body junction. Domain for the DNS simulation


DNS TC04 setup.png
Figure 3: Wing-body junction. Domain for the DNS simulation


Table 1: Wing-body junction. Flow parameters


Boundary conditions

The computational set-up aims at replicating the flow conditions of the experiment but with a halved incoming boundary layer thickness. To enforce these conditions in an efficient and accurate manner a Blasius velocity profile corresponding to and free stream velocity is imposed at the inlet together with uniform static pressure . and total temperature . A laminar boundary layer is then established, and a flow perturbation is applied at to trigger transition to turbulence following the idea of Housseini et al. (2016) and Schlatter and Örlü (2012). The distance of the inlet boundary from the wing-body junction is defined such that the incoming turbulent boundary layer reaches a thickness (half of the experimental value) at a given point, hereinafter referred as checkpoint, upstream the airfoil leading edge, i.e., at . To define such distance, a precursory computational campaign for the turbulent flow over a flat plate was performed. According to the outcomes of this campaign, the inlet boundary is positioned at . The tripping term promoting the boundary layer transition is then located at , see Fig. 2. At the outlet boundary, placed at , the static pressure is imposed with an exit-pressure outflow boundary condition. The bottom boundary is an adiabatic solid wall type (no slip) for and symmetry type for . This choice aims to mitigate spurious perturbations possibly originating at the outlet boundary. Symmetry conditions are imposed at the lateral () and top () boundaries. An adiabatic solid wall(no slip) condition is finally imposed on the wing surface.

References

  1. Apsley, D.D. and Leschziner, M. (2001): Investigation of Advanced Turbulence Models for the Flow in a Generic Wing-Body Junction. Flow, Turbulence and Combustion, Vol. 67, pp. 25–55
  2. Gand, F., Deck, S., Brunet, V., and Sagaut, P. (2010): Flow dynamics past a simplified wing body junction. Physics of Fluids, Vol. 22, 115111
  3. Devenport W.J. and Simpson R.L. (1990): Time-dependent and time-averaged turbulence structure near the nose of a wing-body junction. Journal Fluid Mechanics, Vol. 67, pp. 23–55
  4. Fleming, J.L., Simpson, R.L., Cowling, J.E. and Devenport, W.J. (1993): An experimental study of wing-body junction and wake flow. Exp. Fluids Vol. 14, pp. 366–378
  5. S. Hosseini, R. Vinuesa, P. Schlatter, A. Hanifia and D. Henningson (2016): Direct numerical simulation of the flow around a wing section at moderate Reynolds number, International Journal of Heat and Fluid Flow, 61:117–128
  6. Schlatter, P. and Örlü, R. (2012): Turbulent boundary layers at moderate Reynolds numbers: inflow length and tripping effects, Journal of Fluid Mechanics, 710:5–34




Contributed by: Francesco Bassi (UNIBG), Alessandro Colombo (UNIBG), Francesco Carlo Massa (UNIBG), Michael Leschziner (ICL/ERCOFTAC), Jean-Baptiste Chapelier (ONERA) — University of Bergamo (UNIBG), ICL (Imperial College London), ONERA

Front Page

Description

Computational Details

Quantification of Resolution

Statistical Data

Instantaneous Data

Storage Format


© copyright ERCOFTAC 2024