Description AC4-01
Wind environment around an airport terminal building
Application Challenge 4-01 © copyright ERCOFTAC 2004
Introduction
The subject of this Application Challenge is a study of the wind environment around a large airport terminal building (Figure 1). The building is ~300m long and is roughly rectangular in plan, with an aerofoil-shaped roof. It is located near to one of the main runways of the airport. The surrounding area is relatively open, with a few neighbouring buildings with large plan dimensions but of lower heights.
Figure 1 The airport terminal building, the adjoining runway, and surrounding buildings
This study relates to an actual civil construction project. A comprehensive wind tunnel study was carried out by BMT on behalf of Atkins to assess the effect of ground level winds on pedestrian comfort, internal ventilation, and cladding structural loading.
Since the building is located near one of the main runways, its influence on the wind environment over the runway and its effect on aircraft landing and take-off also had to be evaluated. This is an unusual requirement for building design, and the main parameters that were assessed were the velocity defect and turbulence enhancement in the wake of the building at various locations along, and over, the runway.
The original aim of this Application Challenge was to include all the wind engineering design aspects mentioned above, and to compare the data obtained in the wind tunnel study against CFD calculations. However, due to a lack of sufficient information on certain boundary conditions (details of building openings and internal geometrical detail) available data on pedestrian comfort, internal ventilation, and cladding structural loading were not comprehensive enough for the purpose of CFD evaluation. The only dataset that was sufficiently self-contained and well-defined for this purpose was that of the wind environment over the runway.
For this reason, and despite the fact that it is an unusual wind engineering application, this Application Challenge focuses exclusively on the wind environment over the runway. Previously unpublished data from the wind tunnel study are provided on the velocity defect and turbulence enhancement in the wake of the building. These are used to evaluate the results of CFD modelling carried out by two research organizations, NCSR Demokritos and University of Southampton. © ERCOFTAC 2004 Relevance to Industrial Sector
Modelling the wind environment associated with proposed or existing buildings is of central importance for the Wind Engineering and the Civil Construction sectors, and the potential market for wind engineering studies around buildings is large ([Ref. 1], [Ref. 2]). In the UK, wind studies are currently carried out for an increasing number of buildings, though only the statutory minimum consideration is given for the majority of smaller buildings. This limitation mainly arises as a result of the relatively high cost associated with such studies, which are typically carried out in the wind tunnel. The cost of a wind tunnel study depends on the cost of constructing a detailed model of the building and its surroundings, and increases with the number of measurement locations and the number or complexity of measurement techniques required. By contrast, CFD simulations provide information on all flow parameters in the entire modeling domain, and can offer more flexibility when exploring a variety of building designs and modifications.
CFD could potentially supercede traditional wind tunnel studies as a more cost-effective and powerful design tool for wind engineering studies, leading to a significant expansion in the demand for such services. However, wind tunnel testing is a mature and trusted experimental methodology, whereas quality and trust in the use of CFD for wind engineering applications is still a contentious issue [Ref.2]. © ERCOFTAC 2004 Design or Assessment Parameters
The design or assessment parameters (DOAPs), for this application challenge are the cross-runway velocity deficit and the turbulence intensity excess over the runway in the wake of the building, as a function of wind direction. The correlation of the turbulence and the dominant turbulence length scales (and their comparison with aircraft size) are also important assessment parameters, however these cannot be included in this AC since no such information is available.
Details and guidance on calculating the DOAPs defined above are provided in the documentation of Test Case EXP-1. © ERCOFTAC 2004 Flow Domain Geometry
The building is roughly rectangular in plan, with an aerofoil-shaped roof, as illustrated in Figure 1 (above). It is approximately 300m long by 100m wide and 35m high (~9Hx3HxH). The building length is parallel to the runway, and the distance from the centroid of the building to the centreline of the runway is 456.2m (~13H). The surrounding area is relatively open, with a few neighbouring buildings with large plan dimensions but of lower heights. The location of the building with respect to surrounding buildings and the nearby runway are illustrated in Figures A and B.
The x, y, and z directions, as well as the wind direction, q, are also defined in figure_a.gif. The x‑direction is horizontal along the length of the building (from the West to the East face of the building) and the z-direction is vertically upwards. Wind direction q=0° corresponds to wind normal to the airside (North) face of the building and q=180° corresponds to wind normal to the landside (South) face of the building. Velocity components u, v, w correspond to the x, y, z components of velocity, respectively. © ERCOFTAC 2004 Flow Physics and Fluid Dynamics Data
The flow is fully turbulent, isothermal (neutral atmospheric conditions are assumed), and incompressible. No other physical processes are involved. The only governing non-dimensional parameter (GNDP) relevant to this Application Challenge is Reynolds number (Re). The Reynolds number is calculated based on the height of the building:
Using H=37m and a reference velocity of U=2m/s at z=H, the full scale Re number is ~5x106. The working fluid is air, at standard ambient temperature and pressure.
Due to its roughly cuboid shape, the terminal building is expected to act overall like a bluff obstacle, but its airfoil-shaped roof is streamlined, adding complexity to the behaviour. Due to its dimensions, the terminal building is expected to have the most influence on the flow over the runway, compared to the smaller and lower height neighbouring buildings.
References
[Ref. 1] A Strategy for Wind Engineering research, The Wind Engineering Society (1997), ISBN07277 2489 4.
[Ref. 2] Castro IP & Graham JMR (1999) Numerical wind engineering: the way ahead? Proc. Instn.Civ.Engrs. Structs. & Bldgs. 134, 275-277. © copyright ERCOFTAC 2004
Contributors: Athena Scaperdas; Steve Gilham - Atkins
Site Design and Implementation: Atkins and UniS
Top Next